Straight answers to the garage door problems we get called about most, written in plain English so you can try the easy fix before you pay for a call-out. If your question is not here, send us a photo — we answer messages all day.
Emergency, 24/7Stuck, off track or will not close — three-hour response target
What we repairSprings, cables, motors, remotes, panels and more
Common garage door questions
My garage door stops halfway. What should I do?
Stop using the remote and check for an obstruction in the opening — a car bumper, a box, or a branch. If the door reverses or stops on its own, the safety beam may be dirty or misaligned: wipe both sensor lenses and look for something blocking the beam path. If the opener keeps clicking without the motor running, it is usually a tripped breaker or a tripped motor overload. Send us a photo of the opener light pattern and we will tell you over WhatsApp whether it is worth a visit.
How do I open my garage door during a power outage?
Every opener has a manual release. For a sectional door, pull the red cord handle down and slide the trolley toward the door to disengage the drive — the door will lift by hand. For a roller door, the release lever or cord is usually on the side of the motor housing. Reset the trolley afterwards: with the door on the ground, slide the trolley back along the rail until it clicks into the drive. We fit a battery backup module to about half the doors we work on, which keeps the remote working through a blackout.
My remote stopped working — what should I check first?
Try a second remote or the wall button inside. If only one remote fails, the button battery is usually dead — most remotes take a coin cell or an A23 battery. If the inside button also fails, check that the wall button light comes on and that the breaker is on. Old remotes also lose programming after a power cut; we can re-pair the opener to your remotes on site for a small call-out.
Why does my door bounce back before closing?
A garage door will not close through an obstructed safety beam. The photo eyes sit at the bottom of the opening on both sides — wipe them, then check for a broom handle, a pallet, or a bicycle leaning too close. If the beam is clear and it still bounces, the opener’s force setting may be too low for the door weight, or the door has drifted out of square after a track adjustment. Sensors are the most common thing we replace on a call-out.
Can I replace torsion or extension springs myself?
No. Torsion and extension springs store enough energy to kill, and they are under load even when the door is closed. This is the one job on the list we will always send a technician for. If a spring has already snapped and the door is heavy or hard to lift by hand, stop lifting and call us — we will fit the correct spring for your door weight and cable drum.
My garage door is noisy. What causes it?
Rough grinding usually means dry or worn rollers, hinges or the top bracket. A scraping sound on sectional doors is often a bent track or a panel that has shifted. On roller doors, rattling slats usually need the guide rollers and bearings serviced. We replace rollers and bearings as a set, which is cheaper than chasing one component at a time.
The door is off track or rubbing. Should I keep using it?
Stop running it if the door is visibly off the track or a panel is out of square — the cable can come off the drum and drop the door. Park vehicles clear of the opening and call us. A door that has come off track once usually needs the tracks re-hung and the cables re-tensioned, not just a quick re-alignment.
My door feels heavy. Is that dangerous?
A door that suddenly feels much heavier than it used to is usually a broken or slipped spring, or a failing opener. It is not something to leave — an unbalanced door can come down without warning. If the door stays up and feels heavy, stop using it and call us the same day. We carry torsion and extension springs on the truck.
There is a dent in my door after a car backed into it. Replace or repair?
It depends on the panel. Aluminium and steel sectional panels can usually be replaced individually without replacing the whole door, which is much cheaper. Roller door slats are harder to repair — a curled or crushed slat usually means replacing the affected slats and re-rolling the curtain. Send us a photo and we will tell you which case yours is before you commit to anything.
My roller door slats rattle, curl or look wavy. Can that be fixed?
Curled slats are usually a failed bottom seal or a door that has been driven into from outside, not a spring problem. In many cases the bottom bracket, seals and rollers can be replaced and the curtain re-squared without a new curtain. If the slats themselves are bent, the affected section can be replaced. Send a photo of the door from inside and outside and we will tell you which it is.
Water and leaves are getting under the door. What do I fix?
A gap along the bottom edge is the bottom seal — a cheap part that makes a huge difference and can often be fitted on the same visit. Water tracking in from above is usually a header seal or a misaligned panel. We replace bottom seals, guide brushes and weather strips as part of a standard service, and we will tell you honestly if the door is past the point where a seal is worth doing.
How often should a garage door be serviced?
A standard residential door needs a full service about every 12 months, or every 6 months if it runs more than 15 cycles a day. Commercial and body corporate doors run much harder and should be on a documented schedule. A service covers cleaning and lubricating rollers, hinges, springs and tracks, checking the safety beam and the force setting, and testing the auto-reverse. It is the cheapest way to avoid an emergency call-out.
Can you repair a door or opener I did not buy from you?
Yes, and most of our work is exactly that. We service all major brands across Melbourne — B&D, Merlin, ATA, Gliderol, Steel-Line, Centurion, Taurean, Eco, Grifco, BFT, 4D Doors and more. If a part is hard to source, we say so up front rather than after you have paid to book. If a part turns out to be a dealer-only item, we will tell you and quote accordingly.
How much does a garage door repair cost?
Repairs are quoted from photos and video at no charge, and about 90% of them are priced remotely before anyone books a visit. Call-out is $0 to $149 depending on distance and is confirmed before we come. We do not charge a separate $99 diagnostic fee on top of a repair you go ahead with. New installations are itemised so you can see exactly what you are paying for.
Which brands of garage door and opener do you service?
Doors: B&D, Steel-Line, Centurion, Taurean, Eco, Gliderol, Danmar, Titan and Hörmann. Openers: B&D, ATA, Merlin, Steel-Line, Eco, Grifco, BFT, 4D Doors, Superlift, Chamberlain and Marantec. If you are not sure who made your door, photograph the motor nameplate and the panel and we will identify it for you.
Send a photo of the whole door and a close-up of the motor nameplate. We will tell you what is likely wrong, what it usually costs, and whether it is worth fixing or replacing. No call-out fee just to be told the price.
A number of these answers come down to whether the door is safe. Our guide to Australian garage door safety standards explains the two standards that apply, and the five checks you can run in five minutes.
